Allokit

Allokit traceurs Bluetooth

Activation, installation, safe use and regulatory information for models AK-B1, AK-B1A, AK-B2 and AK-B2A.

4 modelsMagnet activation

Version 1.0 · November 2026

Allokit traceur Bluetooth installed on an air compressor

Identify your model

The Allokit model appears on the product, its packaging or the shipping documents. This manual covers the four models below.

Allokit model

  • AK-B1
  • AK-B1A
  • AK-B2
  • AK-B2A

Activate it with the magnet

Use a magnet to activate the traceurs Bluetooth without opening the enclosure.

AK-B1 · AK-B1A · AK-B2 · AK-B2A

  1. 01

    Locate

    Find the magnetic sensor symbol on the traceur Bluetooth.

  2. 02

    Activate

    Place the magnet over the symbol and hold it there for 3 seconds.

  3. 03

    Verify

    The red LED flashes for 3 seconds to confirm that the traceur Bluetooth is on.

Turn off the traceur Bluetooth

Repeat the procedure by holding the magnet over the symbol for 3 seconds. The red LED remains on for 3 seconds.

Low battery

The red LED flashes twice every 10 seconds.

Keep the magnet away from magnetic-stripe cards, medical implants and any equipment that is sensitive to magnetic fields.

Install and use

The traceur Bluetooth broadcasts a Bluetooth identifier that a compatible Allokit gateway can detect. It does not calculate a GPS position by itself.

Choose the location
Choose a clean, dry and stable surface away from direct impacts. Keep the label readable and avoid fully enclosing the traceur Bluetooth in metal.
Test before mounting
Temporarily place the traceur Bluetooth in the chosen location and confirm that Allokit detects it before completing the installation.
Mount
Use only the mounting hardware supplied with your model or recommended by Allokit. Tighten it only enough to secure the traceur Bluetooth without deforming the enclosure.
Verify
After installing or moving the equipment, confirm that the traceur Bluetooth is stable, undamaged and detected in Allokit.
Detection
For reliable detection, keep the traceur Bluetooth away from large metal obstructions and within the area served by an Allokit gateway.
Modification
Do not paint or drill the enclosure, and do not add any part that could damage the product or cover its label.

Maintain it safely

Inspect the traceur Bluetooth periodically and after a significant impact. A damaged unit must not remain in service.

  • Do not crush, puncture, short-circuit or incinerate the traceur Bluetooth or its battery.
  • Stop using it if the enclosure is open, distorted, unusually hot or leaking.
  • Keep the product and any battery out of reach of children.
  • Do not open the enclosure or attempt to replace the battery.
  • Clean only with a soft, slightly damp cloth. Do not use solvents or pressure washing.

At the end of its useful life, take the traceur Bluetooth to an appropriate electronics or battery collection point. Do not dispose of it with household waste.

Canadian regulatory information

The ISED certification for models AK-B1, AK-B1A, AK-B2 and AK-B2A is held by Allokit inc.

Certification holder
Allokit inc.
ISED certification number
IC: XXXXXX
Covered models
AK-B1 · AK-B1A · AK-B2 · AK-B2A

Notice for licence-exempt radio apparatus

Official notices required by RSS-Gen 6, section 9.3.2.1.

Français

L’émetteur ou le récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

  1. L’appareil ne doit pas produire de brouillage.
  2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

English

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that can cause undesired operation of the device.
Read RSS-Gen on ISED’s official website

Need help?

Include the Allokit model, the number printed on the label and what you observe. Never mail a damaged battery without prior instructions.

Email Allokit

Keep the link to this page with your equipment records so you can always reach the current version of the manual.